EFTA00301420.pdf

OREGENCY Owners & Regency HorizonTM HZ4OE Installation Manual Gas Fireplace MODELS: 14Z40E•NG1 Natural Gas I4Z40E•LP1 Propane WARNING: FOR YOUR SAFETY If the information in these instructions are not followed exactly, What to do if you smell gas: a fire or explosion may result causing property damage, • Do not try to light any appliance personal injury or loss of life. • Do not touch any electrical switch: do not use any phone in your FOR YOUR SAFETY building. Do not store or use gasoline or other flammable vapors and • Immediately call your gas supplier liquids in the vicinity of this or any other appliance. from a neighbour's phone. Follow Installation and service must be performed by a qualified the gas supplier's instructions. installer, service agency or the gas supplier. • If you cannot reach your gas supplier, call the fire department. It,ted by. Installer: Please complete the details on the back cover and leave this manual with the homeowner. EDI Homeowner: Please keep these instructions for future reference. Intertek 919 165 FM FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1144 05/29/12 EFTA00301420  MANUFACTURED MOBILE HOME REQUIREMENTS INFORMATION FOR MOBILE/MANUFACTURED HOMES AFTER FIRST SALE This Regencr product has been tested and listed by Warnock Hersey/Intertek as a Direct Vent Wall Furnace to the following standards: VENTED GAS FIREPLACE HEATERS ANSI Z21.88-2009/ CSA 2.33-2009 and GAS-FIRED APPLIANCES FOR USE AT HIGH ALTITUDES CAN / CGA 2.17-M91. This appliance may only be installed in an aftermarket permanently located, manufactured (U.S.A only) or mobile home, where not prohibited by local codes. This Direct Vent System Appliance must be installed in accordance with the manufacturers installation instructions and the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280, or the current Standard of Fire Safety Criteria for Manufactured Home Installations, Sites, and Communities ANSI/NFPA 501A, and with CAN/CSA Z240-MH Mobile Home Standard in Canada. This appliance installation must comply with the manufacturers installation instructions and local codes, it any. In the absence of local codes follow the current National Fuel Gas Code, ANSI 2223.1 and the current National Electrical Code ANSI/NFPA 70 in the U.S.A., and the current CAN/CGA B149 Gas Installation Code and the current Canadian Electrical Code CSA C22.1 in Canada. This appliance comes equipped with a dedicated #8 Ground Lug for attachment of the ground wire to the steel chassis as applicable to local codes. The appliance, when installed, must be electrically grounded in accordance with local codes or, in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70. or the Canadian Electrical Code, CSA C22.1. This appliance can only be used with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases. Ensure that structural members are not cut or weakened during installation. This appliance may be installed as an OEM installation in a manufactured home (USA only) or mobile home and must be installed in accordance with the manufacturer's instruction and the Manufactured Home Construction and Safety Standard, Title 24 CFR. Part 3280, in the Untied States, or the Standard for Installation in Mobile Homes, CAN/CSA Z240 Mkt, in Canada. W ilkA WARNING! lir HOT GLASS WILL CAUSE BURNS DO NOT TOUCH GLASS UNTIL COOLED NEVER ALLOW CHILDREN TO TOUCH GLASS Regency HorlzonTM HZ40E Gas Fireplace EFTA00301421  To the New Owner: Congratulations! You are the owner of a state-of-the-art Gas Fireplace by REGENCY°. The HZ40E has been designed to provide you with all the warmth and charm of a fireplace at the flick of a switch. The model HZ4OE has been approved by Warnock Hersey/Intertek for both safety and efficiency. As it also bears our own mark, it promises to provide you with economy, comfort and security for many trouble free years to follow. Please take a moment now to acquaint yourself with these instructions and the many features of your Regency Fireplace. ONE REGENCY marmoithu. We recommend that our products be FIREPLACE IRSTRLITC installed and serviced by professionals NFI who are certified in the U.S. by the National Fireplace Institute° (NFI) or in Canada by Wood Energy Technical WoodEmmy Wakeleateleg CERTIFIED., Training (WETT). ONE TREE TM Regency HorlzonTM HZ40E Gas Fireplace EFTA00301422 TABLE OF CONTENTS SAFETY DECAL 4" x 6-5/8" venting 35 High Elevation Gas Line Installation 36 Copy of Safety Decal 5 Pilot Adjustment 36 Gas Pipe Pressure Testing 36 880 S.I.T. Valve Description 36 REQUIREMENTS Aeration Adjustment 36 AC power adaptor installation (for surefire systems) 37 MA Code - CO Detector 6 Wiring Diagram 38 (for the State of Massachusetts only) 6 proflame system GT 38 proflame system GTM 38 INSTALLATION proflame system GTMF with optional fan 39 optional fan Wiring Diagram 40 Without ProFlame GTMF system 40 Important Message 8 Optional Remote Control 41 Before You Start 8 Receiver Wall Switch 41 General Safety Information 8 wall mount On / Off Switch and battery compartment Installation Checklist 9 installation and/or receiver installation 42 Locating Your Gas Fireplace 9 GTMF remote installation 43 Heatwave Duct System 9 Optional fan Installation 46 Heat Release kit 9 Optional fan Installation - into existing installations 47 Clearances 10 Inner Panel Installation 49 Mantel Clearances 11 Glass Crystals or optional ceramic stones 50 Mantel Leg Clearances 11 Optional Pebble / Crystal Installation 51 Unit Assembly Prior To Installation 12 Glass door Installation 52 Nailing Strips 12 Optional mesh glass guard 53 Installation Access panel 12 54 4 piece faceplate installation Front face Nailing strip installation 12 Inner and outer door frame installation 55 Framing Dimensions 13 Non-Combustible Requirements 14 Non-combustible facing installation 14 OPERATING INSTRUCTIONS Framing & Finishing 15 Framing & Finishing 16 Operating Instructions 56 Non-Combustible Requirements 16 First Fire 56 Exterior Vent Termination Requirements 17 Lighting Procedure 56 4" x 6-5/8" Rigid Pipe 18 Shutdown Procedure 56 Cross Reference Chart only 18 Normal Operating Sounds of Gas Appliances 56 Vent Restrictor Position 20 Copy of Lighting Plate Instructions 57 Venting Introduction 21 Maintenance Instructions 58 Venting Arrangement for Horizontal Terminations 21 Glass Gasket 58 Horizontal Terminations 22 Glass Door 58 Flex Vent 4" x 6-7/8" 22 Glass Replacement 58 Horizontal terminations 23 General Vent Maintenance 58 Rigid Pipe 4" x 6-5/8" 23 Valve assembly Replacement 59 Horizontal Terminations 24 Rigid Pipe 4" x 6-5/8" 24 PARTS LIST Vertical terminations 27 Rigid Pipe 4" x 6-5/8" 27 Venting Arrangement for Vertical Terminations 28 Main Assembly 60 Vertical Termination with Co-Linear Flex System 29 Accessories 61 Vertical Terminations 30 Rigid Pipe 4" x 6-5/8" 30 WARRANTY Venting Arrangements - Vertical Terminations 32 Unit Installation with Horizontal Termination 33 4" x 6-5/8" venting 33 The Warranty: Limited Lifetime 63 Unit Installation with Horizontal Termination 34 Unit installation with Vertical Termination 35 Regency Horizon"' HZ40E Gas Fireplace EFTA00301423  SAFETY LABEL This is a copy of the label that accompanies each HZ40E-NG1 and HZ40E-LP1 Direct Vent Gas Fireplace. We have printed a copy of the contents here for your review. NOTE: Regency, units are constantly being improved. Check the label on the unit and if there is a difference, the label on the unit is the correct one. COPY OF SAFETY DECAL Lined: VENTED GAS FIREPLACE HEATER! FOYER AU GAZ A EVACUATION DO NOT REMOVE THIS LABEL r NE PAS ENLEVER CETTE ETIQUETTE Certified for/Leith& pour: CANADA and U.S A. Tested to: CAN/CGA-2.17-M91(R2009) Intertek ANSI 221.88-2009/CSA 2.33-2009 MAY BE INSTALLED IN MANUFACTURED (MOBILE' HOMES AFTER FIRST SALE. litREPN.cT Serial No/ No de aerie 412 4001172 O NATURAL GAS: Model H240E-NG1 APPAREIL FONCTIONNANT AU NATURAL GAS Minimum Clearances to Combustibles I Degagement Minimum De Materisux Combustibles CONCU POUR ETRE POELE: Mode* HZ40E-NG1 Minimum supply pressure 5if WC/C.E. (125IPa) Preston mnimurn Side Walls Manifold pressure 34 WCIC.E. f327IPa) Preston a la aibulum dechappement Neves A Er (203mm) Orifice sue IMO CA1S Grandeur de nnecteur Ceiling Maximum input 26.000 Mufti (7.61 kW) Debt Calonligue maximum salon 8 22' (559mm) Minimum input 18,000 Mufti (5 28 kW) Yaltitude Min. Mantel Height Altitude 04500 Dpi (0-1372m) C 1r (432mm) Max. Mantel Depth O PROPANE GAS: Model HZ40E-LPI EQUIPE A CUISINE POUR GAZ PROPANE 13" (330mm) CONCU POUR ETRE POELE: ModeleHT.40E-LP1 Alcove Width Mnimum supply pressure 11' WC (2.73 kpa) Preston Minimum E 84" (1524mm) Manifold pressure 10' WC1C.E. (2491Pa) Presslon a b turauNre dolchapperneM elevee Alcove Depth Orifice sae #53 CMS Grandeur de I1Mecteur F 36- (2134mm) MaxmLon Input 25.500 Btuiti (7.47kW) DeWI Calorilque maxenum scion DOOR SEAL: Please Minimum Input 21.000 Bbih (6.15 kW) raktude check that the door is lawsuitsction Munui let Altitude 04500 fipl (0-1372m) properly sealed minute:ens) This appliance must be inslallad n aconlance *Mb local codes. if any: if nom. Sow the National Fool Gas Code. ANSI 2223.1. cr Natural Gas and Propane Install on Code. GSA0169.1. This MpliaMe muslin :Walled ine000rdance wen me StandiedCAN:CSAZ2401M. M0bleHousino.in Canada. Or wsb me HanulachgedHolneCcoseucbonandSalgYSlandard. tee 24 CFRP(0 3280.in the Veiled SOWS. C. wails, SW) StaMarO PS Mt apoicams.ANSUKSBCS A225 liNFPASOI A. Mantoactured Horne IntlellatiCOS Standard C•ANSI All 9.20u NFPA SOIC standard reeRecreed4no Wades This appliamo is only forum ailh the type dips irdicalcdrolls recap plate and may be mimed n an aftermarkel. permanently lomat manufactuogrnobilaThomewhere nc4pohlaited bylocal cedes. See vanes manual fordetals. This applance d notoomembie torus, enhothareases.wiless a certifed iutisused. Installer reooenFlselonles codes ourealementsOcata. ou.en rabeence de MK Nolemerts. INICOIOS 01:la 2223.1. National FuelGasCode ouCSA43149.1 en vIgueur Installer repoereil salon le norms CAN'CSA-Z240. Sane WM. MilltiOn MOON, Ou CANCSA-Z240 VC. VOIColOS 00 CaMOIn0. Ou la tonne 24 CFR Pert 3280. ManulaCtunid HOMO Consau(ton and Safety Standard. Si ces norm*,ne pampas acclimates. utilsez le normeANSUNCSBCSA225.1/NFPA 501A. Manufactured Home Installations Standard. ouANSI AI 19 2 ou NFPASOIC Standardfor Recreational Vehicles. Cal apparel don etre dela.unouemem avec to tyDedepa2 ndiove suns plaque signeXHIgue.Cecamaret.o errs ru"s"e O&M. unBmiton preeabnqueeou moDhe le -V. SeuleclaliV)InSIfille daMtoule Si les retflaMenISIOG3us le DaMeltenl Writ WOG Cla IVIIMSSor pets pluSde fenSeirecnertS CSISCOOMII=[OS COnAutible DOurunS ulllexIbOnaveCilliti$2.aSurS. on.IfCuSSOCONDS *SI Vella Thls vented gas fireplace heater is not forme wither Altars. Ne pas utikserde Niro a air avec ce foyerau pas itevacuatIon. FORUSEWITHGLASSDOORSCERTIFIEDWITH THEAPPLIANCEONLY POUR UMISATIONUMOUEMENT AVEC LESPORTESENVERRECERTIFIEESAVEC L'APPAREIL Fan (1Pala 258-911) vase," canals. Fdroon au Canals Ela-tical supply l Electrique 115VAC. 1.13A 6011t NOT FOR USE WITH SOLID FUELS.! NE PAS UTILISER AVEC DU COMEIUSTBLE SOLIDE. FPI Fireplace Products International Ltd. Delta. BC. Canada 9i#166 For the State of Massachusetts, installation and repair must be done by a plumber or gasfitter licensed in the Commonwealth of Massachusetts. For theStateof Massachusetts. flexible con- nectors shall not exceed 36inches in length. For the State of Massachusetts, the appli- ances individual manual shut-off must be a t-handle type valve. The State of Massachusetts requires the installation of a carbon monoxide alarm in accordance with NFPA 720 and a CO alarm with battery back up in the same room where the gas appliance is installed. Regency HorizonTM HZ40E Gas Fireplace EFTA00301424 REQUIREMENTS MA Code - CO Detector (for the State of Massachusetts only) 5.08: flodlfleatIons to NFPA-54. Chapter 10 (2) Revise 10.8.3 by adding the following additional requirements: (a) For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in pan for residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than seven (7) feet above finished grade in the area of the venting, including but not limited to decks and porches, the following requirements shall be satisfied: 1. INSTALLATION OF CARBON MONOXIDE DETECTORS. At the time of installation of the side wall horizontal vented gas fueled equipment, the installing plumber or guiltier shall observe that a hard wired carbon monoxide detector with an alarm and battery back-up is installed on the floor level where the gas equipment is to be installed. In addition, the installing plumber or gasfitter shall observe that a battery operated or hard wired carbon monoxide detector with an alarm is installed on each additional level of the dwelling, building or structure served by the side wall horizontal vented gas fueled equipment. It shall be the responsibility of the property owner to secure the services of qualified licensed professionals for the installation of hard wired carbon monoxide detectors a. In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic. the hard wired carbon monoxide detector with alarm and battery back-up may be installed on the next adjacent floor level. b. In the event that the requirements of this subdivision can not be met at the time of completion of installation, the owner shall have a period of thirty (30) days to comply with the above requirements: provided, however. that during said thirty (30) day period. a battery operated carbon monoxide detector with an alarm shall be installed. 2. APPROVED CARBON MONOXIDE DETECTORS. Each carbon monoxide detector as required in accordance with the above provisions shall comply with NFPA 720 and be ANSUUL 2034 listed and IAS certified. 3. SIGNAGE A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum height of eight (8) feet above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled healing appliance or. equipment. The sign shall read in print size no less than one-half(1f2) inch in size. "GAS VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS". 4. INSPECTION. The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation unless, upon inspection, the inspector observes carbon monoxide detectors and signagc installed in accordance with the provisions of 248 CMR 5.08(2X2)1 through 4. (b) EXEMPTIONS: The following equipment is exempt from 248 CMR 5.08(2)(8)1 through 4: 1. The equipment listed in Chapter 10 entitled "Equipment Not Required To Be Vented" in the most current edition of NFPA 54 as adopted by the Board: and 2. Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate from the dwelling, building or structure used in whole or in part for residential purposes. (c) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM PROVIDED. When the manufacturer of Product Approved side wall horizontally vented gas equipment provides a venting system design or venting system components with the equipment. the instructions provided by the manufacturer for installation of the equipment and the venting system shall include: 1. Detailed instructions for the installation of the venting system design or the venting system components: and 2. A complete parts list for the venting system design or venting system. (d) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM NOT PROVIDED. When the manufacturer of a Product Approved side wall horizontally vented gas fueled equipment does not provide the parts for venting the flue gases. but identifies "special venting systems", the following requirements shall be satisfied by the manufacturer: 1. The referenced "special venting system" instructions shall be included with the appliance or equipment installation alit:Will:MS: and 2. The "special venting systems" shall be Product Approved by the Board. and the instructions for that system shall include a pans list and detailed installation instructions. (c) A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment. all seating instructions. all pans lists for venting instructions. and'or all venting design instructions shall remain with the appliance or equipment at the completion of the installation. Regency Horizon"' HZ40E Gas Fireplace EFTA00301425  DIMENSIONS 45 5/8" PEW 39-13/16' 1 — 1. — . 364- — —Iv :2 a , — 43X1 (1092mm 341,4- (972mm) 48. (1238mrn) 4 (902m1 36" (gum.) mew El Regency I-Icemen' 14240E Gas Fireplace EFTA00301426  INSTALLATION 11)Under no circumstance should this IMPORTANT MESSAGE YOUNG CHILDREN SHOULD BE CARE- appliance be modified. Parts that have SAVE THESE FULLY SUPERVISED WHEN THEY ARE to be removed for servicing should be replaced prior to operating this appliance. IN THE SAME AREA AS THE APPLI- INSTRUCTIONS ANCE. TODDLERS.YOUNG CHILDREN 12) Installation and any repairs to this appliance AND OTHERS MAY BE SUSCEPTIBLE The Gas Fireplace must be installed in accordance should be done by a qualified service person. with these instructions. Carefully read all the TO ACCIDENTAL CONTACT BURNS. A A professional service person should be called instructionsin thismanual first. Consult the'authority PHYSICAL BARRIERS IS RECOMMEND- to inspect this appliance annually. Make it a having jurisdiction"todeterminetheneed for aperrnit ED IF THERE ARE AT RISK INDIVIDUAL practice to have all of your gas appliances prior tostarting theinstallation.It is the responsibility IN THE HOUSE. TO RESTRICT ACCESS checked annually. of the installer to ensure this fireplace is installed TO A FIREPLACE OR STOVE. INSTALL in compliance with manufacturers instructions and AN ADJUSTABLE SAFETY GATE TO 13) Do not slam shut or strike the glass door. all applicable codes. KEEP TODDLERS, YOUNG CHILDREN AND OTHER AT RISK INDIVIDUALS OUT 14) Under no circumstances should any solid fuels OF THE ROOM AND AWAY FROM HOT (wood. paper, cardboard, coal. etc.) be used in BEFORE YOU START SURFACES. this appliance. Safe installation and operation of this appliance 15) The appliance area must be kept clear and free requires common sense, however, we are required CLOTHING OR OTHER FLAMMABLE of combustible materials. (gases andotherflam• by the Canadian Safety Standards and ANSI MATERIAL SHOULD NOT BE PLACED made vapours and liquids). Standards to make you aware of the following: ON OR NEAR THE APPLIANCE. INSTALLATION AND REPAIR SHOULD Emissions from burning wood or gas could BE DONE BY AN AUTHORIZED contain chemicals known to the State of SERVICE PERSON. THE APPLIANCE GENERAL SAFETY Califomia to cause cancer, birth defects or SHOULD BE INSPECTED BEFORE INFORMATION other reproductive harm. USE AND AT LEAST ANNUALLY BY A PROFESSIONAL SERVICE PERSON. 1) The appliance installation must conform with MORE FREQUENT CLEANING MAY local codesor,in theabsenceof localcodes, with the current Canadian or National Gas Codes. BE REQUIRED DUE TO EXCESSIVE CANI -B149orANSI Z223.1 Installation Codes. LINT FROM CARPETING. BEDDING MATERIAL,ETC.IT IS IMPERATIVETHAT 2) The appliance when installed, must be CONTROL COMPARTMENTS.BURNERS electrically grounded in accordance with local AND CIRCULATING AIR PASSAGEWAYS codes, or in the absence of local codes with the OF THE APPLIANCE BE KEPT CLEAN. current National Electrical Code. ANSI/NFPA 70 or CSA C22.1 Canadian Electrical Code. DUE TO HIGH TEMPERATURES, THE 3) See general construction and assembly APPLIANCE SHOULD BE LOCATED instructions. The appliance and vent should be enclosed. OUT OF TRAFFIC AND AWAY FROM FURNITURE AND DRAPERIES. 4) This appliance must be connected to the specified vent and terminationcaptotheoutside of the building envelope. Never vent to another WARNING: FAILURE TO INSTALL THIS room or inside a building. Make sure that the APPLIANCE CORRECTLY WILL VOID vent is fitted as per Venting instructions. YOUR WARRANTY AND MAY CAUSE A SERIOUS HOUSE FIRE. 5) Inspecttheventingsystem annually forblockage and any signs of deterioration. CHILDREN AND ADULTS SHOULD BE 6) Venting terminals shall not be recessed into a ALERTED TO THE HAZARDS OF HIGH wall or siding. SURFACE TEMPERATURES. ESPE- CIALLY THE FIREPLACE GLASS. AND 7) Any safety glass removed for servicing must be SHOULD STAY AWAY TO AVOID BURNS replaced prior to operating the appliance. OR CLOTHING IGNITION. 8) To prevent injury, do not allow anyone who is unfamiliarwiththeoperation to usethefireplace. 9) Wear gloves and safety glasses for protection while doing required maintenance. 10) Be aware of electrical wiring locations in walls and ceilings when cutting holes for termination. Regency Horizon"' HZ40E Gas Fireplace EFTA00301427  INSTALLATION This includes: 4) This appliance is Listed for bedroom INSTALLATION installations using the standard Remote CHECKLIST 1) Clocking the appliance to ensure the correct firing rate (rate noted on label 26.000 Equal (thermostat system). Some areas may have funher requirements. check local codes before 1) Locate appliance (NG).25.500 Btum (LP)after burning appliance installation. a) Room location (Refer to' ocating Your Gas for 15 minutes. fireplace section) 5) The HZ40E Direct Vent Gas Fireplace b) Clearances to Combustibles (Refer to 2) If required. adjusting the primary air to ensure is approved for alcove installations, see 'Clearances" section) that the flame does not carbon. First allow the "Clearances" section for details. c) Mantle Clearances (Refer to "Mantel unit to bum for 15.20 min. to stabilize. Clearances' section) 6) We recommend that you plan your installation d) Framing 8 Finishing Requirements (Refer CAUTION: Any alteration to the product that on paper using exact measurements for to "Framing 8 Finishing" section) causes sooting orcarbonIng that resultsIn dam- clearances and floor protection before actually e) Venting Requirements (Refer to "Venting' age Is not the responsibility of the manufacturer. installing this appliance. Have an authorized section) inspector. dealer. orinstaller reviewyour plans before installation. 2) Position nailing strips (Refer to 'Unit Assembly Prior to Installation). Note: For vent terminations refer to "Exterior Vent Termination Locations" section. 3) Slide unit into place. 4) Remove installation access panel. LOCATING YOUR Heat Wave 5) Install vent (Refer to 'Venting Arrangement' GAS FIREPLACE asvarr---er sections). 1) When selecting a location for your fireplace. ensure that the clearances are met. HEATWAVE 6) Make gas connections (Refer to "Gas Line Installation section). DUCT SYSTEM 2) The appliance must be installed on a flat. solid. 7) Make electrical connections to receptacle continuous surface For example a wood. metal OPTIONAL KIT #946-556 supplied with unit (recommended). or concrete floor or in a raised (on the wall) ap- plication. The appliance must be installed on The HeatWave Air Duct Kit increases the 8) Install 4 AA batteries into receiver/switch box a metal or wood panel extending the full width effectiveness of your fireplace by dispersing warm or use optional AC power adaptor. and depth of the appliance. air from the ireplace to remote locations in the same room or other rooms in your home. 9)Testthe pilot (Refer to 'PilotAdjustmenrsection). 3) The HZ40E Direct Vent Gas Fireplace can be installed in a recessed position or framed out Up to two kits may be installed on the fireplace. 10) TestGas Pressure (Referto"Gas Pipe Pressure into the room as in A. B. C and D. Testing" section). See Diagram 1. Please Note: Only 1 HeatWave kit may be oper- ated at one lime. This includes the internal blower 11) Install standard and optional features. Refer to option as well. the following sections: a) Glass Crystals/ Optional Ceramic TET A alltur>"•=1.0 Wave ," Stones Heat b) Optional Firebox Base Pebbles c) Optional Reflective Panels d) Optional Fan The HeatWave Duct Kit has different e) Faceplate clearance andframingrequirements.cbeck f) Remote Control or Wall Thermostat the HeatWave manual for details. and 10ft. wire harness. 12) Reinstall installation access panel. OPTIONAL 13) Final check. Diagram HEAT RELEASE KIT Before leaving this unit with the customer, the installer must ensure that the appliance is firing A) Flat on Wall #946-570 correctly and operation fully explained to customer. B) Flat on Wall Comer The Heat Release Kit expels warm air from the C) Recessed into Wall/Alcove Comer fireplace to the outside of the building. allowing D) the fireplace to be operated with less heat entering the room. The kit may be used on either the left or right side. Regency Horizon"' HZ40E Gas Fireplace EFTA00301428  INSTALLATION CLEARANCES The clearances listed below are Minimum distances unless otherwise stated: A major cause of chimney related fires Is failure to maintain required clearances (air space)to combustible materials. It is of the greatest importance that this fireplace and vent system be Installed only in accordance with these Instructions. Caution Requirements WARNING The top. back and sides of the fireplace are defined by Fire hazard Is an extreme risk standoffs. The metal ends of the standoff may NOT be if these clearances (air space) to combustible materials are not recessed into combustible construction. adhered to. It is of greatest importance that this fireplace and vent system be installed only in accordance with these instructions. iwites.• r The HeatWave Duct Kit and the Heat ife Release Kit have different clearance Clearance: Dimension Measured From: S and framing requirements. check the HeetWaveand Heat Release manual A: Mantel Height (min.) B: Sidewall (on one side) 1T (330mm) Top of Fireplace Opening lint Release MI for details. 8' :203mm: Side of Fireplace Opening Flue Clearances to Combustibles C: Ceiling (room and/or alcove) Horizontal Top 3" 22" (559mm) Top of Fireplace Opening Horiztonal . Side 2" D: Mantel Depth (max.) 1r (330mm) 22" Above Fireplace Opening Horiztonal • Bottom E: Alcove Width 844 (2134mm) Sidewall to Sidewall (Minimum) Vertical F: Alcove Depth 36' (914mm) Front to Back Wall (Maximum) Passing through wall. G: From Floor 27' (686mm) Top of Fireplace Opening floor/ceiling when F 1 2" Note: 0" No hearth required firestop is used. Installed close to ceiling. E Alcove r Regency Horizon"' HZ40E Gas Fireplace EFTA00301429  INSTALLATION MANTEL CLEARANCES Due to the extreme heat this fireplace emits, the 14 12 10 8 6 4 2 0 mantel clearances are critical. Combustible mantel clearances from top of front facing are shown in the ll l l l l l t l l t l l l diagram on the right. 26- Note: Ensure the paintthat Is used on the mantel Combustible Material and the facing is"high quality" orthe paint may discolour. 20 - Metal Stud (On Edge) 1" (25mm) Facing 22"(559mm) Non-combustible 10- - 17 Standoff 4 0 To Unit Base 2T Top of Fireplace Opening MANTEL LEG CLEARANCES Combustible mantel leg clearances as per diagram